24'' Manual Sewing Shoe Making Machine Shoes Leather Repairs 60x45cm

Notice: Professional hine, please e sure you know how to use it before your order.

Descrtion:
This hine can be used with nylon line and cotton line, can be used with Prince line and lines, . sewing thiness is 5mm.
The distance between the s can be regulated, and the . width is about 6mm
Can sewing different material shoe by nylon or cotton wire.(Such as cloth shoes , rubber shoes , leather shoes , sneakers , high heels , as well as raincoats , leather bags , cloth , trousers, or leather products.

Operating Instructions:
1. Preparation before operation:
* Press the foot and avoid the friction between the foot and the pin plate.
* Che the fastening of fixed screws in each department.
* Add oil to each part of the oil.
* The shaking guide plate can be used without the sound of kazak.
2. Threading and lead:
*. Take the shuttle shell and the ndle: shake the guide plate, lift the to the highest position, remove the shuttle with tweezers, lift and push the plate, and remove the shuttle with tweezers.
* ndle winding:
Pull off the winding hine, pull out the wire wrap around the center of the ndle for a few weeks into the spool, shake the guide plate to be wraed around the center of the shuttle, and pull ba the winding.
* The center of the shuttle will first transmit the thread of the ndle to the line hole of the shuttle money, and then insert the ndle into the shuttle, and then the thread will be inserted into the hole of the suace to pull the line.
* Put the position of the ndle is hanuide plate, the was about to rise, the ndle end to at the groove, and the thread take 2 to 3 inches long, according to the bed and a half months have flown groove close plate again, shaking the market, but the bottom line to the plate, ped quily put the ion of the error, the bottom line with online and offline.
* Wearing noodles:
Shake the guide plate, lift the to the top position, and put down the foot. Pull out the line head in the coil, thread through the middle shaft, through the thread and line, through the thread spring and thread, enter the hole of the , and then pull the line through the hole to pull the line head 2-3 inches.
* Leave the front of the line in the left hand (not too tight), and use the right hand to shake the guide plate, so that the belt line will p through the pin hole to draw the bottom line, and together with the bottom line, the hine press the foot left behind.
3. Relationsh between the bottom line and mending quality:
* Identification of s.
* Adjust the bottom suace , tight line screw nut SongYa line, use time is too long, there will be a bottom line for too fast, the adjustable or bobbin change line into line, the bottom line, the take-up fixed screw loosening, pi bar baward, che whether the bobbin rong flexible, use sandpaper sanding, tighten the line pressing nut stitch length adjustment.
4. Adjustment of spacing
Because the sewing material is different must adjust the pitch, when choosing the length, need to screw the pitch screw loose, in choosing the to be short time, conly upward move, can.
5. Adjustment of foot
When the must be increased, the must be tightened, and the tension of the tension spring will be increased, and the of the foot will be increased.
6. Handling and sewing of hine :
* Turn the guide plate, the bar up to the top n pine clamp screw, remove the old , insert the flat face new rod inside the groove, touch the bottom of the channel of the hine when the positioning gear, then tighten the screws.
* Combination of and stitching: generally use 18 pin, sewing various kinds of rubber shoes and bag side shoes, such as , 14-16, sewing various leather shoes and canvas, etc., with 18 pins.
7. Adjustment of the ion of the sotto: many people can't draw the line, the reason is that the position is wrong.
When output ndle is to take off the line, the tail end of the shuttle must at the groove, the from a lot, misplacing of ndle position, not timing will be adjusted, loosen the loose piece with screw rod links, moving rod, can e the tail end of the ndle on the groove, then tighten the screw.
8. The adjustment of the bar up: in the stage of , hole should be on the ndle bottom plane, or it should be adjusted, method is to loosen the screw on the small connecting rod shaft, move the bar to the right position to tighten again.

Specification:
Material: Steel
: Green + Sier
Size: 60x45cm

Paage included:
1 x Shoe Sewing hine
1 x User Instruction